IMPLEMENTATION OF TRIZ METHOD TO IMPROVE PAVING PRODUCTION PROCESS (CASE STUDY: INDUSTRIAL ENGINEERING DEPARTMENT WORKSHOP, UNDIL)
Keywords:
TRIZ, Quality, Pavement, ProductAbstract
The purpose of this study is to improve the quality and efficiency of road pavement products to meet consumer expectations. To achieve the quality of road pavement products in this study, the Theory of Inventive Problem Solving (TRIZ) method will be applied. The data used in this study are primary data obtained directly from operators in the Industrial Engineering Department, such as observation data in the design and data in the form of information on the quality of road pavement product production. While secondary data is obtained from books, newspapers, the internet or other media that support the study. From the results of the data analysis, contradictions were finally determined such as Not according to composition / not standard Measurement accuracy (28) vs Loss of time (25), Perforated Pot (29) Manufacturing accuracy vs (25) Loss of time, Lack of knowledge 33 (Ease of operation vs 35 (Adaptability, versatility of manufacturing quality) (29) fabrication) vs 11 (Stress or pressure) and Bad Mal (11) Volume of moving objects vs Difficulty detecting and measuring (37). Alternative Solution for Perforated Pot: In the production process, there are always obstacles to Perforated Pot, for this reason, producers must add clamps to the wind pipe so that they can control wind power. Alternative Solution: Lack of Knowledge because so far there has been no provision or training regarding the production process.
References
J. S. C. Neyland, J. Mende, and M. E. Rembet, “Aplikasi Metode Servqual dan TRIZ Untuk Peningkatan Kualitas Layanan di,” J. Ilm. Manaj. Bisnis Dan Inov. Univ. Sam Ratulangi, vol. 9, no. 1, pp. 42–53, 2022.
R. C. Nugraha and K. Haryono, “Metode TRIZ Untuk Meningkatkan Kreativitas Dan Inovasi pada Bidang Bisnis dan Manajemen Melalui Aplikasi Berbasis Mobile,” Pros. Autom., vol. 3, no. 2, 2022, [Online]. Available: https://journal.uii.ac.id/AUTOMATA/article/view/24190
A. Hakim rohmatulloh, Nugraha, and D. Shofi Mulyati, “Usulan Perbaikan Kualitas Produk Kemasan Kardus untuk Meminimasi Kecacatan dengan Menggunakan Metode Triz,” Bandung Conf. Ser. Ind. Eng. Sci., vol. 3, no. 1, pp. 322–331, 2023, doi: 10.29313/bcsies.v3i1.6699.
G. Guarino, A. Samet, and D. Cavallucci, “SynCRF: Syntax-Based Conditional Random Field for TRIZ Parameter Minings,” Int. Conf. Agents Artif. Intell., vol. 3, no. Icaart, pp. 890–897, 2024, doi: 10.5220/0012411300003636.
Alfin Arif Rochim and Ari Zaqi Al Faritsy, “Perbaikan Kuliatas Arang Briket Menggunakan Metode Six Sigma Dan Triz,” Mars J. Tek. Mesin, Ind. Elektro Dan Ilmu Komput., vol. 2, no. 1, pp. 19–32, 2024, doi: 10.61132/mars.v2i1.55.
F. I. Oktavian and Aviasti, “Perbaikan Kualitas untuk Mengurangi Tingkat Kecacatan pada Produk Kain Grey dengan Menggunakan Metode Teoriya Resheniya Izobreatatelskikh Zadatch (TRIZ) di PT. Dewy Textile Factory,” Bandung Conf. Ser. Ind. Eng. Sci., vol. 3, no. 1, pp. 118–127, 2023, doi: 10.29313/bcsies.v3i1.6073.
H. J. Almuhari and J. Jazuli, “Integrasi Metode RCA dan TRIZ dalam Menyelesaikan Masalah Produksi Bata Ringan (Studi Kasus di PT. X),” J. Tek. Ind. Terintegrasi, vol. 8, no. 3, pp. 2529–2542, 2025, doi: 10.31004/jutin.v8i3.46253.
M. Djunaidi, H. A. Khairunnisa, I. Pratiwi, and E. Muslimah, “Integration of SQC and TRIZ to Reduce Batik Fabric Defects in The Dyeing and Scouring Process at PT. Batik Danar Hadi,” J. Ilm. Tek. Ind., vol. 6869, pp. 247–258, 2025, doi: 10.23917/jiti.v24i02.15253.
